These stylish downlight fittings will enhance the aesthetics of any room. Our range of fittings are suitable for both 12v MR16 (normal halogens) and 240v GU10 lights. Our range of high quality and designer fittings make replacing your downlights easy.
The Todae 240 Volt GU10 Downlight Converter Kit is perfect if your current halogen globes are using too much energy and blowing too often. By installing this converter, you will be able to use 240v GU10 downlights throughout your home. This will substantially reduce the amount of power used to provide lighting in your home, without compromising on the light output. 12v transformers (iron core or electronic) tend to used anywhere between 10-20 watts of power alone! That's not including the power used by the 50w halogen globe! This fitting allows the use almost any GU10 downlight including 11w CFL Downlight & 9w CFL Downlight replacement bulbs which & provide a comparable strength of light and last up to 10 times longer. This unit can be attached to most existing halogen down light fittings to allow conversion from 12v to 240v. Most fixed and regular tilt fittings are compatible with this adapter. However, some units, such as a full-tilt gimble fitting, may not work with this kit.
The CeeLux Series is a family of attractive LED powered recessed light fitting designed for ceilings, walls and overhead shelving. They feature mounting clips for easy installation. The sealed unit with the LEDs integral to the downlight style fitting is especially suited to circumstances where heat retention within the room is important. These fittings operate at a low temperature ensuring safety in the surrounding ceiling space.
The CeeLux HB13 is an environmentally friendly downlighting fitting that consumes just 13 watts of power. With a clean anodised aluminium finish, the CeeLux is attractive and unobtrusive for residential and commercial spaces.
The CeeLux HB13 produces light output equivalent to a 35 watt halogen bulb.
The EDMC Series is a switched mode power supply designed to deliver constant voltage to LED modules and packages. With its compact size, low cost and high efficiency design, the EDMC Series is the perfect companion to deliver power to a range of LED products.
The EDMC Series is a switched mode power supply designed to deliver constant voltage to LED modules and packages. With its compact size, low cost and high efficiency design, the EDMC Series is the perfect companion to deliver power to a range of LED products.
This approved, fire resistant enclosure isolates recessed downlights from the many hazardous elements such as dust, allergens and insects common to ceiling spaces and prevents these elements entering your indoor environment 24 hours a day, seven days a week.
Recessed downlights are a very popular form of lighting for many good reasons. They are classy, streamlined, space efficient, effective and they can highlight particular features of interest.
However without a fire resistant enclosure, downlights are left exposed above your ceiling and can become the foundation for a string of undesirable consequences. Over time, loose material builds up around any high temperature globe.
Isolite seals the back of the downlight inside the ceiling, offering vital benefits in safety and energy reduction, and suits most good quality 12 volt downlights.
Isolite's unique anchoring system resists forces produced by air movement, people and/or rodents. Our downlight guards are manufactured from lightweight high temperature fire resistant materials approved by the Electrical Safety Authorities in Australia.
Contents: 2 piece unit which suits 94mm ash 114mm cut out downlight fittings
Megaman 60° GU10 Reflector Downlight Fitting. These fittings will compliment any room and allow you to increase brightness of the lights over preferred areas. The fittings are recommended to be used with 9 or 11 watt compact fluorescent lamp (available on our site).
Lamp Not included. Must be installed by licensed electrician.
The Possum Electronic Transformer will save you electricity and money by reducing the amount of electricity used in your lighting. The transformer uses 4w as opposed to 15w of conventional transformers.
*Based on an average of 6 hours per day at a cost of 13c/Kwh.
The REDBACK Transformer is the perfect choice for modern, uncomplicated installation of low voltage halogen lighting. The redback uses only around 2W per globe making it far more efficient than standard transformers, and is also suitable for use with our LED lights.
The Redback Transformer is suitable to be used with any 12v downlights including halogens and LED's.
The REDBACK is compact in size, universally dimmable, simple to wire and competitively priced.
The REDBACK Transformer complies with all the relevant requirements and standards relating to safety, performance and electromagnetic compatibility (EMC) for Australia and New Zealand. ET REDBACK is highly reliable with added features like short circuit and overload protection. When used with halogens, it can be dimmed with leading-edge and trailing-edge phase dimmers.
Designed in Australia for Australian conditions, the REDBACK transformer features simple North/South wiring with large primary terminals for easy loop in/out installations (Up to 2 x 2.5mm2 TPS cable). This means that the units are much easier to install with optimised wiring space and installation time.
This Scandinavian inspired modern rectangular design set of 1 light, is ideal for any areas that require ‘soft’ lighting. The protective cover reduces contact with insulation and sound transmission and the 11W lamps are equivalent to a beautiful 60W.
A perfect light for around the home, workshop, shed or office; cabinets, cupboards, pantries, wardrobes or desks. The D.I.Y light is ideal can light up any small area, to make your life easier and to light up those space that are usually dark and difficult.
- Add- on fitting with link cables
- Ideal for under or inside cabinets, cupboards, pantries and wardrobes
- Low voltage, super bright 6W, Warm White (3000k), 30,000 hours CFL
- Up to 4 light units can be linked together and connected to a single transformer (not included)
Contains: one white square CFL light fitting plus link cables and mounting hardware
Look at the new Brushed Silver Tilt Downlight Fitting. These fittings will compliment any room and allow you to angle your light to suit your needs. Once installed they will give you the freedom you want with your lighting. The fittings can be used with GU10 fittings.
Lamp Not included. Must be installed by licensed electrician
Pocket Garden - FlowersOnly $12.95
Shop By Category
Joseph Joseph Index Chopping Board PlusOnly $150.00
Dimple Down VaseOnly $49.95
Free Loader Pico Solar ChargerOnly $39.95
Todae Envirosax Summer PackOnly $44.95
Click Clack Wooden TankOnly $14.95
Cassette USB HubOnly $14.95
Manly MintsOnly $5.95
Joseph Joseph Elevate Set Gift BoxOnly $99.95
